Fasto LockSeal HS is high strength, anaerobic thread locker & sealant. LockSeal HS cures when confined in the absence of air on close-fitting metal surfaces. LockSeal HS is slightly oil tolerant, so it will bond some ‘as received' parts, but best results are obtained with clean substrates. LockSeal HS to be used for locking & sealing where high strength opening is required. LockSeal HS prevents corrosion of assembled parts.TYPICAL APPLICATIONSFasto LockSeal HS is suitable for most medium and coarse threads. Fasto LockSeal HS is formulated to lock & seal all metric and imperial nuts and bolts, preventing vibration loosening and leakage through the threads. LockSeal HS is typically used in crushers, diesel generators, agricultural machines, Hydraulic assemblies, heavy engineering machineries and many more industrial & automobile assemblies.TYPICAL APPLICATIONSFasto LockSeal HS is suitable for most medium and coarse threads. Fasto LockSeal HS is formulated to lock & seal all metric and imperial nuts and bolts, preventing vibration loosening and leakage through the threads. LockSeal HS is typically used in crushers, diesel generators, agricultural machines, Hydraulic assemblies, heavy engineering machineries and many more industrial & automobile assemblies.TYPICAL CURING PERFORMANCECure speed vs. Temperature All figure relating to cure speed are tested at 21°C. Lower temperatures will result in slower cure. Heating the assembled part accelerates the curing process. Activator Fasto AP49 should be used when the temperature is less than 5°C. Cure speed vs. bond gap The size of the bond gap greatly affects the speed of cure of anaerobic adhesives. Bond gap varies with thread type and size of the fastener. The larger the gap between surfaces, the slower the cure speed. Maximum recommended gap for Fasto LockSeal HS is 0.15mm. Cure speed vs. Substrate Cure speed and strength vary according to the substrates. When used on mild steel and brass components Fasto LockSeal HS will reach full strength more rapidly than on more inert materials such as stainless steel and zinc dichromate. Anaerobic Adhesives only cure in the absence of air with metal part activation. Cure speed vs. Activator Where speed is too slow or the bond gap is very large, Fasto AP49 Activator may be used to accelerate cure speed. The use of an accelerator may reduce bond strength up to 30%. Fasto recommends testing on the parts of measure the effect. TYPICAL ENVIRONMENTAL RESISTANCE Hot strength Fasto LockSeal HS is suitable for use at temperatures up to 150°C. At 150°C the bond strength will be ~45% of the strength of at 21°C.Heat ageingFasto LockSeal HS retains over 90% full strength when heated to 100°C for 90 days then cooled and tested at 21°C. Chemical / Solvent Resistance Fasto LockSeal HS exhibit excellent chemical resistance to most oils and solvents including motor oil, leaded petrol, brake fluid, acetone, ethanol, propanol and water. Anaerobic adhesives and sealants are not recommended for use in pure oxygen and chlorine lines .

Fasto Lock Seal is a medium to high strength, anaerobic thread locker & sealant. Lock Seal cures when confined in the absence of air on close-fitting metal surfaces. Lock Seal is slightly oil tolerant, so it will bond some ‘as received’ parts, but best results are obtained with clean substrates. Lock Seal is thixotropic so prevents run off, dripping and migration after assembly. Lock Seal to be used for sealing where high strength opening is required. Lock Seal prevents corrosion of assembled parts. TYPICAL APPLICATIONS Fasto Lock Seal is suitable for most medium and coarse threads. Fasto Lock Seal is formulated to lock & seal all metric and imperial nuts and bolts, preventing vibration loosening and leakage through the threads. Lock Seal is typically used in crushers, diesel generators, agricultural machines, Hydraulic assemblies, heavy engineering machineries and many more industrial & automobile assemblies.

Fasto A143 is a general purpose, medium-high strength, very fast curing and high performance thixotropic anaerobic threadlocker. Fasto A143 is formulated to lock all metric and imperial nuts and bolts, preventing vibration loosening and leakage through the threads. A143 is oil tolerant, so it will bond ‘as received’ parts, but best results are obtained with clean substrates. The thixotropic nature of the product prevents run off, dripping and migration after assembly. The product cures when confined in the absence of air on close-fitting metal surfaces. TYPICAL APPLICATIONS Fasto A143 is suitable for most medium and coarse threaded screws, nuts and bolts. Fasto A143 is typically used on mounting bolts, housing screws, cap screw of industrial static & dynamic machines. Fasto A143 can also be used for threadlocking applications of automobile assemblies. A143 prevents corrosion of assembled parts

Fasto A170 is fast curing thread locking compound that where regular removal for maintenance is not required. It is recommended for permanently locking of studs on engine blocks and pump housings. Features: High performance Permanent strength Works against corrosion Prevent loosening Good temperature resistance

Boss PU 25 is a fast-curing one-component polyurethane sealant that turns into a flexible, durable and resistant elastomeric seam and has a very good adhesion to most industrial materials. Boss PU 50 has high elasticity and excellent tear, vibration and weathering resistance. Easy to apply, it adheres without primer to the most common substrates such as glass, anodized aluminum, lacquered metal, wood, FRP and concrete. Specifications of Boss PU 50 Polyurethane Sealant meets or exceeds the following: TT-S-00230C9(Type ll) Class A ASTM C-920 Type S Grade NS Class 25, Use-NT, A and M Typical Properties: Specific Gravity 1.2-1.3 Skin formation time 40mins Curing speed 4mm per 24 hours Shore hardness Approx.50 Elongation at break >700% Tensile Strength 2.3N/mm2 Tear Strength 8N/mm2 Color Black, Grey & White Features: Primer less adhesion to most substrates Excellent weather ability Paintable Tools Easily

Born2BondTM Light Lock MV is a low-odor, low-blooming, dual curing (contact and lightcuring), cyanoacrylate adhesive. It is designed for bonding applications that require fast fixturing coating or surface cure. The UV- and visible-light cure sensitivity allows rapid bonding through transparent parts and quick curing of light-exposed bulk or surface-coated areas, while the instant bonding capability ensures cure between opaque substrates (contact cure). KEY FEATURES → Dual cure formulation: instant and photo-cure → Fixture time in 60 s (without light exposure)* → Can be cured with visible and UV-LED light <5 sec → Long open time without activation → Dry to touch, tack free surface cure → Cure-on-demand of excess material released from bondlines → Bonds, fills, reconstructs and coats → Low odor, low blooming → Available in a range of viscosities: MV, HV and Gel

Description • Hybrid adhesive sealant based on MS base. • Ultra transparent, crystal joint and free of isocyanates and solvents • excellent adhesion to wide range of construction and automotive substrates • Adheres without primer to most of the substrates. • Works on damp condition, UV resistance and Paintable • Neutral, non-corrosive and applicable on alkaline surface • Suitable for both internal and external applications, odourless and chemical resistance • Bonding skirting-boards, panels, plates made of synthetic materials, glaze, terracotta, elements made of synthetic materials, wood, metals, metal plates, for all types of surfaces in building such as brick, concrete, gypsum, plasters • Shore A hardness: 45 • Skin formation time: 5-50 minutes • Product meets requirements of EN 15651-1:2012 F-EXT-INT-CC • Product meets requirements of EN 15651-3:2012 S Class S 2

Fasto UV98E is a single component, general purpose,very low viscosity and economic grade UV adhesive thatcures to give a clear, flexible bond when exposed toUVA-light. It is especially suited for decorative glassbonding. The low viscosity of UV98E means it can wickinto preassembled parts.TYPICAL APPLICATIONSFasto UV98E is general purpose UV adhesive that hasbeen developed for bonding glass where non yellowing,transparent bonding is required.It is mainly developed for glass furniture industry wherehigher precision and transparency is required.PROPERTIES OF UNCURED MATERIALValueChemical type Urethane acrylic esterAppearance ClearSpecific Gravity 1.03Viscosity cPs1Typical Value 57Fixture Time2 (secs) 5Depth of Cure3 (mm) 2Compress Shear Strength4, N/mm2Glass 10Refractive Index 1.35Hardness ShoreD 48Shelf Life @ 21°C (months) 12Operating Temperature Range (°C)Continuous -50 to +110Intermittent -50 to +1301 Brookfield LVF, Spindle2 , 30rpm2 Glass slide fixture 10mW/cm2 @ 365 nm3 Cured for 30 secs @ 10mW/cm2 @ 365 nm4 Based on ASTM D2095-69, 180 secs cure @ 20mW/cm2 TYPICAL CURING PERFORMANCEGlass Slide Fixture Time in seconds, using Hg VapourLamp:10mW/cm2 <530mW/cm2 <3The rate of cure, depth of cure and surface tack of thecured adhesive will depend on the intensity of the UVlight, exposure time, and spectral output of the UV lightsource and light transmittance of the substrates to bebonded.Depths of cure up to 8mm can be achieved with highintensity lamps and long cure times. To achieve a fast,controlled, reproducible cure performance, the use ofhigh quality UV lamps is recommended.Cure Speed vs. IntensityFasto UV98E can be cured using sunlight. However, fora controlled, repeatable cure, UV lamps should be used.Cure speed vs. bond gapFasto UV98E is designed for bonding closely fitting glassand metal parts. UV98E can be used to a maximumdepth of ~3mm.CURING MECHANISMFasto UV98E is formulated to cure when exposed to UVradiation of 310nm or above.Chemical / Solvent ResistanceFasto UV98E exhibit excellent chemical resistance tomost oils and solvents including alcohols, methylatedspirit water. Fasto UV-curing adhesives are notrecommended for use in pure oxygen or chlorine lines.DIRECTIONS FOR USEFasto UV98E is very sensitive to UV-light. The adhesivesshould be applied to clean, dry parts. Ensure parts are clean, dry and free from oil and grease. Apply adhesiveto one surface. Once the adhesive is applied, the partscan be positioned correctly and then exposed to UV-lightto initiate curing. Ensure that the entire bond is exposed.Product can be hand applied from the bottle.Dispensing systems are also available for high volumeassembly applications. Feed lines for the dispensingsystem must have black, UV-opaque tubing to avoidadhesive curing in the lines. Please contact your Fastorepresentative for further advice on dispensing solutions.GENERAL INFORMATIONFor safe handling of this product consult the MaterialSafety Data Sheet.StorageStore in a cool area and out of direct sunlight.Refrigeration to 5°C gives optimum storage stability.PackagingBottles: 100 g, 250 g and 1 kg. Available in bulk for usewith dispensing system.Please note: When packed an air space above theProduct is vital to maintain stability.DATA RANGESThe data contained in this data sheet may be reportedas typical value and/or range. Values are based onactual test data and are verified on a regular basis.NOTESThe information contained herein is produced in goodfaith and is believed to be reliable but is for guidanceonly. Fasto India and its agents cannot assume liabilityor responsibility for results obtained in the use of itsproduct by persons whose methods are outside orbeyond our control. It is the user's responsibility todetermine the suitability of any of the products and methods of use or preparation prior to use mentioned in

Fasto A333 is a single component, super-fast curing and super high strength anaerobic retaining, locking & sealing compound. Fasto A333 is formulated for retaining, locking & sealing cylindrical parts. Fasto A333 is also designed to augment the strength of press fit and slip fit assemblies. Fasto A33 is specially designed for cylindrical assemblies where power transmission is important. Fasto A333 offers excellent heat resistance. Once applied, parts slip together easily, lubricated by the adhesives. Fasto A333 cures when confined in the absence of air between close-fitting metal surfaces. Fasto A333 prevents corrosion of assembling parts. TYPICAL APPLICATIONS Typical applications include retaining & locking of sleeves, bushes, bearings, pulleys, sprockets, gears, etc onto shafts. Fasto A333 is also used for retaining rotors, plugs and many more cylindrical assemblies. It can also be used for sealing & locking threads where very high strength is required. Typically Fasto A333 can be used in motors, pumps, gearboxes, turbines, compressors generators, shower panels and many more industrial & automotive assemblies.